One dead burner on a four-burner range changes how a whole family eats. Call our referral line and we route you to an independent stove pro near Bryan who works on gas, electric coil, smooth-top and induction cooktops.
Stove problems look simple from the kitchen and often are not. That is why we route your call to independent pros who spend their days on burners, igniters, switches and glass tops.
Every contractor we connect you with runs their own licensed, insured business. Gas work on a range touches a supply line, so ask the pro about their gas certification for your area before work starts.
You see the number before a screwdriver turns. The pro gives you a written, upfront quote after the diagnosis, and the choice to proceed is yours.
We work the local schedule while you are still on the phone. Same-day visits happen often when a nearby pro has an open slot, and the dispatcher pins down a time window before you go.
Expect a manometer, a digital multimeter, an orifice set, and tech sheets for slide-in, freestanding and pro-style ranges. The right tools mean the first visit is usually the one that gets the burner going again.
Freestanding ranges, slide-in ranges, drop-in cooktops, induction surfaces and the heavy pro-style rangetops with open burners all come through our line. The problem is almost always on top: a burner, an igniter, a switch, a control board or the glass itself.
Tell the dispatcher the brand, whether it runs on natural gas, propane or electricity, and exactly which burner misbehaves. That short description helps the pro bring the right igniter, element or valve on the first trip.
Most stove calls fall into one of these groups. Each one needs different parts and a different test, which is why we ask a few questions before we dispatch.
Constant clicking with the knob turned off often means a spill soaked the switch harness under the knobs. No spark at all on every burner points the pro toward the spark module or its power feed.
A healthy flame is crisp and blue. Yellow tips, lazy flames or flames that lift off the ports point to clogged burner ports, a misaligned burner cap, a dirty orifice or a regulator problem. The pro clears the ports, reseats the cap and head, and checks pressure with a manometer.
When a coil burner stays cold, the culprit is usually the element, the receptacle block it plugs into, or the infinite switch behind the knob. A scorched or melted receptacle has to be replaced along with its wiring terminals, or the new coil will fail too.
A crack in a smooth-top is more than cosmetic: spills can reach live elements underneath. The tech tests the radiant element and limiter, checks the hot-surface indicator, and quotes a new glass top if the old one is damaged.
Blinking codes, a zone that will not detect the pan, or a cooktop that shuts down mid-boil are classic induction calls. The technician checks the cooling fan, generator board and coil connections with the service manual open.
Stripped knobs, stiff valve stems and gas valves that leak by are common on busy kitchens. The pros also convert cooktops between natural gas and LP orifices and install the anti-tip bracket that keeps a freestanding range from tipping onto a child.
Bring these notes to the phone call. The pro confirms the cause with real tests before quoting a part.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Clicking that will not stop | Wet or shorted valve switch, cracked igniter | Switch continuity, harness, igniter gap |
| No spark on any burner | Spark module or power supply | Module output and incoming voltage |
| Yellow or lifting flame | Clogged ports, wrong orifice, pressure off | Ports, cap seating, manometer reading |
| Coil only heats on high | Failed infinite switch | Switch cycling with a multimeter |
| Smooth-top zone stays cold | Radiant element or limiter open | Element and limiter resistance |
| Induction error code | Cookware, fan or power board | Code lookup, fan, board voltages |
The process is short on purpose. You call, a local pro shows up, you see a quote, and the burner gets tested in front of you.
One phone call starts everything. Tell us what the cooktop is doing, and we look for a nearby pro with time on the schedule.
A local pro heads your way with cooktop parts on board. The dispatcher tells you the arrival window before you hang up.
After testing, you get a plain explanation and a written quote from the technician. You decide whether the fix makes sense for your range.
Once the part is in, the technician lights or powers every burner, checks flame or heat on each setting, and leak-tests any gas fitting that was opened.
A careful pro pulls the cooktop or lifts the top before guessing. On gas units they check pressure at the manifold; on electric units they read voltage at the switch and resistance at the element. That is how a cheap igniter does not turn into an expensive control board by mistake.
Our dispatch line is answered day and night.
The igniter on our gas range would not quit clicking after a boil-over. The pro pulled the knobs, traced it to one wet switch under the panel, replaced it and tested every burner before he left.
I own a couple of older rentals and one tenant reported a burner that smelled hot. The technician found a melted receptacle block on the coil range, replaced it with new terminals and a new coil, and showed me the scorched wiring. Glad we caught it.
My induction cooktop kept flashing an error and shutting off in the middle of cooking. The tech checked my pans with a magnet first, which was fair, then found the cooling fan was jammed with grease. Cleaned and replaced the fan, and it has run fine since.
We moved into a house with propane and brought our natural gas range. The dispatcher found a pro who converted it the next morning, swapped every orifice, flipped the regulator and checked the flames burner by burner. He also put in the anti-tip bracket the old owners never installed.
Nonstop clicking usually means moisture or grease has reached a valve switch or igniter, so the spark module thinks a burner is still asking for a spark. Sometimes drying it out helps, but a shorted switch needs replacing.
It is worth treating as a warning. Healthy burners show a firm blue flame. Yellow tips point to a dirty burner, a misaligned cap, or gas pressure that is off, and the technician can confirm it with a manometer.
Cut the power or the gas first. On electric ranges, flip the breaker; on gas ranges, close the shutoff behind the unit. Then call and we will route a pro who can replace the switch or valve that failed.
A crack lets liquid reach live parts, so the glass has to be replaced. The technician quotes the new top in writing, and most models allow the glass to be swapped without replacing the whole range.
Yes, in most cases. The conversion involves new orifices sized for propane, a regulator change, and low-flame adjustments on each valve. Ask the technician to leak-test every fitting when the job is done.
Start with a magnet test on the pan. Aluminum, copper and some stainless pans will not work on induction. If the cookware checks out, a pro can read the error code and test the generator board and fan.
Our referral line covers homes, condos, apartments and rental properties in Bryan and the nearby neighborhoods and suburbs. The independent pros we connect you with drive to you, and most carry common igniters, coil elements and switches on the truck.
Landlords and property managers use the line too, since a dead burner in a rental becomes an urgent tenant call fast. Tell the dispatcher who will be home to let the technician in.
Gas, electric or induction: call and we will find a pro near you.
